HOME » NEWS » NEWS

Installation and adjustment steps of glass door clamp

The installation and adjustment steps of the glass door clamp are as follows:

<a target='_blank' href=''><strong>glass door clamp</strong></a>.jpg

First, positioning and putting on line

The glass door is composed of fixed glass and movable glass door leaf.

According to the technical drawings, the positioning line of the glass door is released, and the position of the door frame is determined at the same time.

Limit slots on the top of the mounting frame

The width of the limiting groove should be two to four millimeters thicker than the glass, and the groove depth is ten to twenty millimeters. At the beginning of installation, two edge lines of metal decorative board are drawn out from the line of the bomber, and then the limit grooves on the top of the door frame are installed according to the edge lines, and the depth of the grooves in the slot is adjusted by the glued pad.

Third, install the wooden base with metal finish

Fix the square wood on the ground, and glue the metal decorative panel to the wood with universal glue. If an aluminum alloy square pipe is used, it can be fixed on the frame column with aluminum angles or fixed on wooden bricks buried in the ground with wood screws.

Fourth, install the vertical door frame

Then the center line of the bullet is nailed to the door frame square wood, then the shape and position of the door frame column are determined by plywood, and finally the metal decorative surface is outsourced. When covering the surface, place the head-to-head seam on the middle door positions on both sides of the glass.

Five, install glass

Use a glass sucker to suck the thick glass tightly and lift the thick glass plate to the installation position. First insert the upper part of the glass into the limiting groove on the top of the door frame, and then place the lower part of the glass on the bottom bracket.

Six, fixed glass

Nail two small square wood strips on the inside and outside of the base square, sandwich the thick glass on the middle door, apply the universal glue on the square wood strips, and glue the decorative metal on the square wood strips.

Seven, glass glue seal

On both sides of the top limit slot and bottom bracket notch, as well as the gaps between the thick glass and the frame column, etc., inject the glass glue to seal, and scrape off the excess glass glue with a tool.

Eight, glass docking

When the fixed part of the glass door needs to be spliced due to its large size, the width of the seam must be 2 to 3 mm, and the edge of the glass plate must be chamfered.

Nine, floor spring installation

Before the door leaf is installed, the ground spring and the positioning pin on the top surface of the door frame should be installed and must be coaxial. It is best to check with the hanging line to ensure that they are on the same straight line.

Ten, install the upper and lower door clamps

The upper and lower metal door clamps are respectively installed at the upper and lower ends of the glass door leaf. If the height of the door leaf is insufficient, the wooden bottom can be padded with wooden planks.

Eleven, fixed glass door door clamp

After setting the height of the door leaf, insert small wooden bars into the gap between the glass and the upper and lower door clamps, and inject glass glue into the gap to fix it.

Twelve, door leaf installation

First, adjust the positioning pin out of the plane of the beam by two millimeters with its own adjusting screw, and erection the glass door of the office. Sleeve on the pin shaft, rotate the door leaf at right angles to the door frame beam, align the rotating connection hole in the door clamp on the door leaf with the positioning pin on the door frame beam, adjust the adjustment pin adjustment bolt, and insert the positioning pin into the hole.

Thirteen, handle installation

Before installation, apply a little glass glue to the part where the handle is inserted into the glass. When the handle is assembled, press the fixing screw tightly to ensure that the handle is not loose.

GLASS TOOLS

TEL.:+86-750-3876878

E-mail:info@jmjiangyi.com

GLASS HARDWARES

TEL.:+86-750-3876731

E-mail:jiangyi_maple@jmjiangyi.com

BATHROOM ACCESSORIES

TEL.:+86-750-3876831

E-mail:jyhardware_maple@jmjiangyi.com

Sitemap